Ground Breeding System for Breeding Hens: Layout and Equipment

A ground breeding system for breeding hens is a floor-based house where hens and roosters live together on a mix of raised slats and litter, so natural mating happens. Fertility and hatchability depend on four layout decisions: slat-to-litter split, nest placement, separate male and female feeders, and stocking density.

Why breeder flocks live on the floor

Commercial layers only need to lay eggs, so a cage with hens alone is enough. Breeder hens must lay fertile eggs, which means roosters have to be in the same pen and able to mount freely. That single requirement drives almost every layout choice below.
Some operations house breeders in cages and use artificial insemination instead. That is a different labour and skill model and is outside this guide, which covers natural-mating floor houses only.

The layout decisions that matter

Slat and litter zones
The common arrangement raises a slatted area above the manure and leaves a litter area at floor level. Drinkers sit over the slats so spilled water drains away from the litter. The proportion between the two zones comes from the breed guide, not from the equipment supplier, so ask for the zone ratio in writing before you accept a drawing.
Slat material and edge finish are worth checking early. Mugong’s documented durability positioning applies to its galvanized and aluminized-zinc structures.

Nest placement

Eggs laid on the floor are dirty, harder to collect and less suited to hatching, so the nest layout is really an egg-quality decision. Nests belong where hens naturally walk to, along the edge of the slatted area, away from drinkers and away from the brightest or draftiest part of the house. The nest count and the rows’ length are again breed-guide numbers.

Separate feeding for males and females

Hens and roosters have different body-weight targets and feed allowances, so a single shared feeder line does not work. The usual fix is two feeding lines: hen feeders with a grill opening too narrow for a rooster’s head, and male feeders hung above hen reach. When males eat hen feed, they gain weight and fertility drops; when hens cannot reach feed, laying drops. Both failures show up weeks later, long after the layout is fixed.

Stocking density and ventilation

Floor area per bird, feeder length per bird, drinker count and nest count all multiply out from one stocking figure. Overstock the house and you get wet litter, crowded feeders and floor eggs together. Ventilation then has to remove the moisture that litter holds, which is why the house design and the equipment list should be agreed together, not in separate quotes.

How to plan a breeder house layout, step by step

1. Get the current parent-stock management guide and write down its allowances for floor space, nests, feeder length and drinkers per bird. Done when every later number traces back to this page.
2. Set the flock size per house, then multiply each allowance by it to get required floor area, nest count and feeder length.
3. Split the floor into slat and litter zones using the guide’s ratio, and put drinker lines over the slats.
4. Place the nests along the slat edge and mark every floor-level corner where hens might lay instead.
5. Specify two separate feeding lines, one for hens and one for males, with the hen grill size and male feeder height written into the drawing.
6. Check ventilation, manure handling and vehicle access against the house layout.
7. Review a scale drawing with the supplier and confirm that no hen is further from a nest, feeder or drinker than the guide allows.

Ground system or cage-based layer equipment?

Compared with the catalogue-style listings common on supplier sites, where a breeder floor system appears as a single line item, a layout-first approach starts from the allowances and works out to the equipment. That is the order I recommend for any quote request.

Costs: what is and is not published

What moves the quote:

• bird capacity per house
• manual, semi-automatic or fully automatic equipment
• galvanized or aluminized-zinc structure
• depth of climate control (ventilation, cooling, heating)
• whether the house is a steel-structure building
• destination country (freight, certification, installation)
• scope: equipment only, or turnkey EPC

Sending these seven items with the request shortens the quoting cycle.

Häufig gestellte Fragen

 What is a ground breeding system for breeding hens?

A floor-based house where hens and roosters share one pen on raised slats and litter, so natural mating produces fertile eggs. Nests, feeders and drinkers are laid out around the slat and litter zones.

 Why do breeder houses use two feeding lines?

Hens and males have different feed allowances and body-weight targets. Separate lines, with a hen grill too narrow for a rooster’s head, stop males eating hen feed.

How many hens per nest, and how many birds per square metre?

Both come from the management guide for your genetics line. This guide gives no figure without a verified source, so use the supplier’s current document.

 Can I use Mugong’s broiler floor equipment in a breeder house?

Mugong lists it for broiler houses and publishes no breeder specification. Ask Mugong’s engineers to confirm what a breeder layout would need added.

 What does a breeder floor system cost?

Quote only. Send bird capacity, automation level, structure material, climate-control depth, house type, destination and scope to get a project figure.